logoinsert.gif (1964 bytes) left_top_ban.gif (667 bytes) top_ban_pic.gif (319 bytes) right_top_ban.gif (423 bytes)
left_bot_ban.gif (582 bytes) Engine right_bot_ban.gif (148 bytes) right_bot_ban.gif (145 bytes)
nav_bar_top.gif (287 bytes)Home
Engine
Cooling System
Body
Interior
Roll Cage
Frame Mods
Suspension
Steering
Fuel System
Transmission
Rear End
Exhaust
Brakes
Links
Other Rangers
Drawings
nav_bar_top.gif (287 bytes)
nav_bar_bot.gif (2214 bytes)
 12.gif (44 bytes)12.gif (44 bytes)  

I purchased an inexpensive set of sheet metal valve covers at one of the races, welded in the

fitting / bungs / oil fill cap that I needed and then polished the heck out them!  Don't know how

long they'll stay that purty - we'll see.  I'm about to get all my accessories hooked up, be ready

to start soon!

I decided to 'freshen up' the motor before putting it back.  New bearings, gaskets and look things

over real good.  Had a rear main seal leak, you can see the groove wore in the crank and my fix -

a Speedi-Sleeve.  Made a tool to remove the pilot bearing by turning down a bolt to fit thru the

bearing snugly, then pumping the end of the crank full of grease, tapping the bolt in hydraulically

pushed the bearing out.  Ford windage tray & Moroso pickup.  Moroso pan, ARP head studs &

 Fluidamper.  Twisted wedge heads & valve train going on.  Weiand Stealth dual plane intake &

motorplate.  Steel flywheel, Ram clutch & bellhousing.  Finally back in the truck.

 I've started collecting parts for the next motor...

   

The stock rubber motor mounts are showing signs of dry rotting, so I decided another upgrade

 was in order - a motor plate.   I have purchased a CSR electric water pump and a Moroso

 vacuum pump.  The vacuum pump needs to be under driven and I have a 6" pulley on the

 crank, so I purchased this 7.5" pulley from GZ Motorsports.  This pulley bolts right on to the

Moroso pump and will allow me  to run everything on the one serpentine belt which is important

as I don't have a lot of room between the radiator and motor.

I've got the vacuum pump & belt tensioner ('85' Mustang part) mounted, belt installed and test run - OK.

I had to make several custom brackets (I'll post pics of them soon) that have been temporarily

'spacered' with stacks of washers.  I purchased some solid aluminum rod that I will make accurate,

custom spacers with - and use all stainless allen head  bolts.  (Yes I'm going to repaint the alternator)

Engine - 03.jpg (379275 bytes) Engine - 08.jpg (383074 bytes) Engine - 04.jpg (378352 bytes)   

 

I built the 5.0 from scratch several years ago.  It's a good 'starter' motor, but I have

 plans for something a little wilder in the future.  Motor currently includes the following:

 

bulletNew 5.0 block from Summit
bulletTrick Flow 'Twisted Wedge' aluminum heads, box stock
bulletWeiand 'Stealth' dual plane intake
bulletHolley 600 cfm carb
bulletKeith Black pistons
bulletFord Motorsports  X303 hydraulic roller cam
bulletFord Motorsports aluminum roller rocker arms
bulletMoroso 7 quart rear sump Mustang oil pan
bulletFord Motorsports windage tray & oil pump
bulletMSD billet distributor and 6AL ignition
bulletFluidamper Harmonic Balancer
bulletFord Motorsports Steel Flywheel

 

When I originally installed this motor, I used an L&L bracket kit.  This kit allowed

installation of all the power accessories with a single belt tucked close to the motor

for radiatior clearance in the Ranger.  When I removed the AC & power steering,

I installed a March Performance pulley/bracket kit.

 REngine2.jpg (261258 bytes) REngine1.jpg (274050 bytes)